Frequently Asked Questions
|
|
|
|
|
|
|
Q. Is it safe to install the KayaTank TM into my kayak?
|
|
Q. What happens if my tank gets a hole in it?
|
|
Q. How long will the KayaTankTM and Thru-hull fittings etc. last?
|
|
Q. Will the water in the tank slow me down or make my kayak unstable?
|
|
Q. Is it hard to Install?
|
|
Q. Can I still store my rods inside the hull of the kayak?
|
|
Q. Can I put the pump and through-hull outlet in a different place than the instructions say?
|
|
Q. What is a Timer Switch and why do I need one?
|
|
Q. What does Hand Tighten mean?
|
|
Q. What are scuppers and seat supports?
|
|
Q. How many Rod Holders do I need on my Kayak?
|
|
|
|
|
|
|
|
Q. Is it safe to install the KayaTankTM into my kayak?
A. Yes! When installed properly, the KayaTankTM is very safe, because it is made from materials used for boats in the marine environment.
|
|
Q. What happens if my tank gets a hole in it?
A. So far, not one tank has had a hole in it in over 9 years. However, if you run your knife through it, or you put a rock fish in there (not recommended) and a back spine pricks a hole in it, we will send you a patch for your tank. You can patch it in minutes without taking the tank out.
|
|
Q. How long will the KayaTankTM and Thru-hull fittings etc. last?
A . They will last as long as your kayak under normal use, and can be replaced very easily if broken.
|
|
Q. Will the water in the tank slow me down or make my kayak unstable?
A. Most kayak fishermen don't notice any slowing effects or any added tipsiness when paddling or sitting still in their kayak with the bait tank full. Some or even most of the water in the tank is below the waterline, depending on the kayak and how much payload (you and your gear weigh) the kayak is carrying. This water below the water line acts as ballast for your kayak rather than an elevated tipping weight. So it actually increases the stability. Water weighs 7.48 lbs per gallon, so it is better to have this weight below the waterline, where you don't notice the added weight.
|
|
Q. Is it hard to Install?
A. No doubt, some will think it is easy, and some will think it hard. But, if you can install a flush mount rod holder, you can install this KayaTankTM. We have complete instructions on line to view before you buy. Plan to relax and spend the weekend on it, and it will probably get done in a day.
|
|
Q. Can I still store my rods inside the hull of the kayak?
A. Yes. You can still run the rods down the sides of the kayak on either side of the KayaTankTM . Running the rods down the inside of the kayak does put some wear on them, and you can bend an eyelet doing it. Most people strap the rods to the deck. The rods can get some abuse strapped to the deck also, so it's a personal preference.
|
|
Q. Can I put the pump and through-hull outlet in a different place than the instructions say?
A. Yes. The placement of the pump and thru-hull outlet can go in a bunch of different areas. The only criteria is that the pump inlet has to be below the waterline in order to pick up the water, and Outlet thru-hull has to be lower than the Outlet fitting on the KayaTankTM. The greater the distance (vertically) from the Outlet fitting on the KayaTankTM and the Outlet Thru-Hull on the kayak the better for water discharge. As they approach the same height the slower your tank will drain the excess water pumped in.
|
|
Q. What is a Timer Switch and why do I need one?
A. A Timer Switch is a device that turns your pump on and off automatically for you. It is really nice to have one because it allows you to carry a smaller battery, saving weight and money, and can extend the life of your pump too.
|
|
Q. What does Hand Tighten mean?
A. Hand tighten refers to the nuts on the plastic thru-hull fittings, and is the same as threading the nut with a wrench or pliers and stopping when all layers have engaged one another, and you start to feel resistance.
|
|
Q. What are scuppers and seat supports?
Scuppers are tubes that drain water off your kayak. They connect a deck area where water would normally puddle (footwell, tankwell, seat area) with a tube that lets the water drain back into the ocean. They also act a structural supports for the kayak, like in the seat area.
|
|
Q. How many Rod Holders do I need on my Kayak?
A. I think there should be a minimum of 5 rod holders on the kayak. Most kayak fishermen carry a minimum of 3 rods, one for bait and two for fishing. A lot of kayak fishermen carry 4 rods. It is nice to have one more rod holder than rods, in order to move them from position to position effectively. Four rod holders should be behind the seat, and one should be in the front. Two of the rod holders behind the seat should orient the rods in opposing trolling positions about 45 degrees out from the center line, and tilted back about 30 degrees from vertical. The other two rear rod holders can be oriented straight up for rod storage and be located between the two trolling positions. The rod holder in the front is usually used for rigging or changing lures, but can also be used for trolling. The Scotty rod holder can be a good choice for the front. I like flush mounted rod holders, but it is a personal preference.
|
|
| |
|
| |
|
|
|
|
